Direct Manufacturer DSL light not on with Opticomm : r/nbn
When using Opticomm you want to have a WAN light not a DSL light. You connect to it via ethernet cable, not DSL cable. However, when the on the phone, with guidance from the technicians on the
Direct Manufacturer [OpenWrt Wiki] PHICOMM K2
The PHICOMM K2 PSG1218 is a wireless router with both 2.4 GHz and 5 GHz radios. It has five Fast Ethernet ports, later revisions featuring five Gigabit Ethernet ports, and a moderately fast processor.
Direct Manufacturer Phicomm M1 : Operation Manual
Open Port: The port or port range used by the remote system when it responds to the outgoing request. A response using one of these ports will be forwarded to the PC that triggered this rule.
Direct Manufacturer Optical ports not working | Switching
We are experiencing issues with our optical ports between QFX5100 and EX4300 since we rebooted our EX4300 switch. On our EX4300 the switch port is showing as down when I look at the status and the
Direct Manufacturer Optical ports not working | Switching
Hello, I wonder if someone can help. We are experiencing issues with our optical ports between QFX5100 and EX4300 since we rebooted our EX4300 switch. On our EX4300 the switch port is
Direct Manufacturer How Do I Get My Optical Cable to Work: Troubleshooting Tips and
If you''re experiencing difficulties with your optical cable and are wondering how to get it to work, this article will provide you with troubleshooting tips and tricks to help you resolve common
Direct Manufacturer PHICOMM K3 wireless not working · Issue #11466 · openwrt/openwrt
Probably because of this commit 6603748 change the Interface name to "wlan0" or "wlan1" works fine
Direct Manufacturer 10gig optic port goes down with remote fault, need...
I have an extreme switch recently configured, the optical port is not working very good. The link state is always active for a while (couple - 25208
Direct Manufacturer 25g ports on N540-24Z8Q2C-M are not working correctly
I''ve gotten all the other ports (10g and 100g) to correctly turn green when an sfp or qsfp is plugged in and doing "show controllers optics x/x/x/x" shows that the laser state is on so i know that
Direct Manufacturer How to Set Up a Phicomm WiFi Router: Full Configuration Guide
Step-by-step guide to accessing, configuring, and troubleshooting Phicomm routers (K3C, K2, KE2P). Covers default login, IP address, password reset, and key settings — no guesswork.
Direct Manufacturer User Manual
Rear Panel LAN/WAN: This Ethernet port can be used as a LAN or WAN port. USB: Connect to your USB device. Reset: Long press and hold the button for 8 seconds, the Router will reboot to its factory
Direct Manufacturer Fiber port of switch does NOT working
2960X switch = 1/4 port is currently plugged with Cisco GBIC module. - I plugged new Fiber cable with new GBIC module, but switch port is NOT working (no blinking).
Direct Manufacturer 10G SFP+ will not link up
I had light coming through the fiber patch cable but the port would not go active, I could not even get a link light on the switch (X440-G2-48P-10GE). I made sure the port was enabled and
Direct Manufacturer Re: Optical Monitoring not working ICX7450/ ICX7550
Hi Chandini, A case was opened on Wednesday, May 01, 2024. Case 01700836: Digital Optical Monitoring is not working on all Ruckus1G SFPs
Direct Manufacturer Fiber optic cable connection to switch not working
I am currently working in a project which uses a 12 core SM fiber optic cable running 40 km. Switched are connected in ring topology. Distance between two switches will be max 8 km and i
Direct Manufacturer Odd speed issue using a Microtik router and Phicomm switch
Plugging into the WAN port of the Microtik, my computer (which is hardwired to the switch on a 3ft cable) is only able to get 140 Mb/s at Fast . Even stranger, when I connect directly to the Microtik I can
Direct Manufacturer Back Button
Hier sollte eine Beschreibung angezeigt werden, diese Seite lässt dies jedoch nicht zu.
Direct Manufacturer Troubleshooting Fiber Cables : r/networking
There is a single mode optical fiber cable in our datacenter going from a Cisco N5K to another N5K across different racks. The link appears to be dead and I''m hoping to fix it, but I have little to no
Direct Manufacturer The optical link doesn''t work
Hi, everyone! I have problem with optical link (1000SX) on Cisco Catalyst 9300 (C9300-48T). This switch C9300 uses GLC-SX-MMD transciver but port don''t up. Confuguretion this port:
Direct Manufacturer PHICOMM K3(bcm53xx) wireless not working
Probably because of this commit 6603748 change the Interface name to "wlan0" or "wlan1" works fine
Direct Manufacturer Why Is My SFP Not Working?
If any of this info doens''t match the database on the switch, the OS will mark the SFP as not supported and disable the port. The fiber connection
Direct Manufacturer Re: Optical monitoring not possible on ports with link down?
Just posting this response if someone new comes across this topic. I have been using the following switches: ICX7450,7550,7750 and 7850. By default, ports that are down are not included
Direct Manufacturer Installing SFP Fiber Optic to connect two ProCurve Switches not working
I had fiber optic lines put in from one side of building to the other so i can install a ProCurve switch few hundred feet away. I purchased J4859C-AO Network Upgrade adapters. My
Direct Manufacturer Optical Module Application: Common Problems & Troubleshooting
Based on typical issues encountered with optical modules in daily switch applications, this document summarizes basic troubleshooting steps for resolving common faults: